Showing posts with label closet. Show all posts
Showing posts with label closet. Show all posts

Saturday, April 11, 2015

Building the Wardrobe Closet and more...

In the previous post I had just gotten started on the framing for the walls of the wardrobe closet, so now we will continue with that and move on to the smaller short closet across from it. That cabinet is being built specifically to store Sharon's accordion in the bottom, and provide a place for file folders in the upper part.

We also have other musical items to figure out where to store, the largest being my guitar and our Yamaha PSR 500 keyboard. We also have a Suzuki Q-Chord, which is a sort of electronic guitar, but it is in a hard case and is less than 3 inches thick, so it can store almost anywhere. We're not sure how all these will be used yet, other than for our own enjoyment. We just know that we don't want to dispose of them. But we'll worry about those details later.

The wardrobe closet...


The last you saw of the closet was one wall laying in pieces on the saw table. The next step was using the Kreg pocket hole jig (example shown below)...

Kreg Pocket Hole Jig like mine...courtesy Home Depot.
And these are pocket holes...courtesy woodgears.ca.

...to drill the angled screw holes to secure all the parts together. Once that was done, I cut blocks of rigid foam insulation to fill the voids. This was just a strengthening measure because the outer side of the walls was going to be covered in 1/8th-inch paneling. There's not much strength to that, and without some kind of backing, would be like the skin of a bass drum. Not that we plan on fastening anything to it, but it just makes it seem more solid. I chose not to add horizontal cross supports, because the walls will be screwed into cabinets on each side at the mid-point.

The two closet walls with rigid foam board installed.
Once the foam was installed, the outer side of each wall was covered with the 1/8th-inch paneling. However, since my stock of such paneling was limited, and no one will see the bottom of the walls after they are in place, I used some other paneling on the bottom half. On the left side, the bulkhead wall and narrow closet will come up to 40 inches high, so my good paneling started at a height of 39 inches, just to allow for an inch of overlap. On the right side, which will have the kitchen cabinet against it, the standard height for a kitchen countertop is 36 inches, so I made sure the good paneling extended from 35 inches on up. Anything below these two heights will never be seen again, so I just used some scrap paneling...more as a spacer than anything else. If you look closely at the photo below, you can see the slight color difference between the blonde paneling at the top, to the scrap honey oak paneling on the bottom.

The outer side of the wardrobe closet walls.
On the inside, I used some cheap 3/8ths-inch CD plywood, as it is going to be painted over. I just gave it a light sanding, and it will be OK, for what it is being used for.

The left side wall of the wardrobe closet set in place.

Before the walls were covered with the heavier plywood, I made several trips back and forth to the trailer to adjust the cut of the top of the walls, and then when it fit like it needed to, I scribed the contour onto the 3//8ths plywood before attaching it. In the photo above, you can see the left wall in place against the short and narrow cabinet that was built previously.


The next step was to add the right side wall of the wardrobe closet.

In the photo below, you can see the right side wall. The contour at the top, against the ceiling, may not be perfect, but as one of my former contractor employers once told me..."it's good enough for who it's for." I'll eventually trim everything out (that's paneled) with some thin and narrow cove molding and flat trim, and any painted surfaces will be caulked with painter's caulk, so it will be fine for our purposes.

The right side wall of the wardrobe closet in place.
Note the angled opening at the top of the wall. This will be used as a "chase" or "tunnel" for the wiring for the trailer, and be covered with an angled plywood panel. I chose to do it this way, because of the walls of the trailer being only 1-1/4 inches thick, and the need to use rigid foam board for insulation. It would be far too shallow for electrical boxes, and too difficult to deal with wires, especially the heavier romex cable wires for electrical outlets. Rather than put them "in" the walls, all electrical outlets will be mounted in or on the cabinets. In some cases they may be in the bottom of overhead cabinets, and in other cases, they may be mounted in or on the sidewalls of the base cabinets.

There will also be an angled corner chase down the back right side of the wardrobe closet, to get wires from above down to the battery compartment, which will be in the bottom right side of the wardrobe closet. From there, will also be a pipe running along the floor behind the battery compartment to the rear storage closet, where the incoming shore power will be mounted and distributed from the left wall of that compartment. More on that later.

The other reason for not putting the wiring in the walls, is that if we ever decide to trade this trailer for a new model, and one size larger (7 x 14), it will make it easier to remove everything and add it back into the new trailer. I don't want to have to start another one from scratch again!

Due to the way the door jamb had to be built, it would have been very difficult to attach it to the walls before installation of the closet, and be able to stand them up inside the trailer. The jamb was in three pieces, each designed to interlock with each other for strength. Each side has to be installed on the corresponding wall first, and then the header section installed last.

I forgot to take a picture of the detail of the door jamb, but basically, it is composed of three parts, (1) the outer casing, which is just 3/4 x 1-1/2-inch stock, same as the cabinet facings, (2) the jamb, which in this case is twice as deep as the door, since the bi-fold closet doors will fold back on each other and require 3-1/8 inches (more detail of that later), and (3) another piece of 3/4 x 1-1/2-inch stock for the door stop on the inside. All of these parts were glued and stapled with 1-1/2-inch pneumatic staples.

The wardrobe closet with the door jamb in position.

Keep in mind, the door jamb is not yet fastened to the walls, nor are the walls secured to anything. Only the slight tension against the ceiling is holding them in place at this point. Before they can be secured, the kitchen cabinet must be built and butted against the right side wall, and secured to it. Only then can the correct door width be established.

We already know that the door must maintain a 30-inch width from top to bottom, but the very best way to get a good fit is to mount the doors in the jamb first, to make sure we have not only equal spacing all the way across the top of the doors and down the sides, but to align the bottoms of the doors with the face of each other so they are flush in the front.

To secure this in place before that is done could cause severe mis-alignment problems and make the whole project seem crooked. But we CAN do the final assembly of the door jamb, which needs to be clamped, glued and secured with staples at the top, and then tipped back into place and joined to the walls on each side. But before we can shim the top above the header and screw the header to the ceiling, we must make sure everything is lined up where it belongs.

The trailer itself is not parked dead level due a slight slope in the ground, so using a carpenter's level is useless. The best thing to do in cases like this is to use a 4-foot drywall T-square off the floor to get a "close" idea, and then attach the components (which also must be built perfectly square) to each other, and let them "find their own center". This will also help reduce stress incurred once the trailer is being towed down the road.

The right side wall of the wardrobe closet at the bottom.

The single most critical issue with alignment is the bottom of the right side of the wardrobe closet, shown above. Since these walls are so thin, and pre-assembled, there is no way to anchor the bottom to the floor without something showing. This is why the kitchen cabinet must be installed first, as it will be screwed to the outer trailer wall and to the closet wall, and THAT is what will hold the wall in place and retain proper spacing and alignment for the closet doors.

Later on in this project, we will add the short dividers in the bottom of the closet, to separate the porta-potty from the battery compartment, and also create a storage compartment behind the porta-potty. On the floor, we will also use a piece of 3/4-inch plywood with two cutouts the exact size of the batteries. This, along with a couple of small ratchet straps anchored to screw eyes in the floor will secure the batteries in place. We certainly don't want two 77-pound projectiles going anywhere while on the road! These dividers will also help to strengthen and secure the walls of the closet.

The wardrobe closet from the back of the trailer.
In the photo above, you can see what will be exposed of the wardrobe closet at the back, at least for now. The rear bunk will be on top of the bulkhead wall, with a piano hinge mounted directly on top of the wall. This will allow the front part of the bunk and mattress to be  lifted to gain access to the narrow storage cabinet. The mattress will be 4-inch multi-density foam, specially made for this purpose, so it will cover the first 4-inches of the closet wall that you see.

Keep in mind that once the rear bunk is completed, this view will not be seen from the rear of the trailer. There will be a vertical wall just inside the rear ramp door to close off the back of the rear sleeping compartment, and it will be insulated. My original design calls for a couple of small Plexi-glass windows that can be opened on hinges from the inside, with screens on the back side, just to allow a little ventilation during times when we can have the ramp door open. Otherwise, the storage compartment will be totally sealed off from the living quarters. So the only one who will see the left closet wall will be whomever sleeps in the rear bunk.

The "accordion closet"...


So this brings us to the next stage of the project...the "accordion closet". This short closet will be on the opposite side of the wardrobe closet, just behind the piano and against the bulkhead wall.

For those just finding this page on the web, yes we are taking a piano with us! You'll have to go back to the "New Beginnings" post to catch up with that explanation!

In the photo below, you can see the basic framework for the cabinet, but it has a ways to go yet.

The basic framework for the "accordion closet".
This cabinet will only be exposed on two sides, plus the top. We are again choosing the blonde paneling for the side facing the piano, as at least part of that wall will be visible to the front. And again, it is only 1/8th-inch paneling, so we added rigid foam to the left side as a backer for the thin paneling.

The "accordion cabinet" with rigid foam installed on the left side.
The right hand side will be against the already finished wall of the rear bulkhead, so to conserve weight, I decided to leave that wall  open. After adding support pieces for the bottom and the shelf for holding file folders (or eventually other things, once we can go mostly "paperless"), the left side wall was covered inside and out with paneling. Then I carried the assembled cabinet out to the trailer.

The "accordion cabinet" left side.
Sharon's accordion is one of the heaviest I have ever seen, at roughly 46 pounds, maybe due to the fact that it has electronics for plugging into an amplifier if necessary. I used to play one many years ago, and owned two of them, and mine were nowhere near this heavy! Of course, hers is not a cheap one like mine were, either.

For the floor of this cabinet, as well as the upper shelf, I used 3/8th-inch CD plywood, and it is reinforced on all four sides with framing under it. The framing is glued and stapled to the outer frame.

The right side of the "accordion cabinet".
On the inside, I also used the same blonde paneling as the rear bulkhead wall, so if one looks inside the cabinet, both sides will be the same. Eventually, doors will be made for all these cabinets. The top part of this cabinet will get a "dummy" drawer front, as there is no need to get into it from the front. The rear bunk will cover it most of the time, and if we need to get into it, we will simply lift the front part of the bunk and reach in from the top.

The "accordion closet" set into place in the trailer.
After moving some of my stored items in the trailer, I was able to set the cabinet into place. Again, I am not securing it at this point. I still have to anchor the rear bulkhead wall on each end, and then, due to a slight difference in how square the floor is in regard to the sidewalls, some shims will have to be used before any screws can be installed to permanently anchor the cabinets. It appears the center of the floor is sightly lower (about a 1/4-inch) than the bottoms of the side walls. The same situation applies to the opposite wall. Some shims will have to be used under the cabinets and closet walls to push the tops against the outside walls of the trailer.

Due to the fact that the rear bulkhead wall is built straight, and remains level in the center, the shims cannot be used against the outer walls, as that would make the cabinets out of square with the bulkhead wall as well as anything else in the trailer. The shims MUST be placed under the front edge of the cabinets. Once the kitchen cabinet is in place all of these other lower cabinets can be properly aligned and secured...not before.

For those paying attention, you might realize that this cabinet now protrudes farther forward in the trailer than it's narrow mate on the other side. Originally, they were supposed to be the same width, but due to having to add 4 inches to the storage compartment, they are now slightly "offset". This is not a big issue, although it may appear odd. It will force us to cut the front part of the mattress and platform to allow for this offset. The foot end of the bunk will be above this cabinet, so it will make the foot of the bed wider than the head end...but that isn't a big deal. When we lift the front part of the bed to get into the cabinets underneath, we will likely have a barrel bolt on the mattress platform to hold it up. 

Going forward...


Next up will be the modification of the closet doors, only because I have temporarily run out of "one by" stock to build the rest of the cabinets. That material will be purchased later this week. So in the meantime, I have to find alternative things to do. 

After the closet doors, we'll get back to the kitchen cabinet, and later on, the front couch. For those just joining us, the air conditioner is also being installed in the front couch, so it will require more than a simple framework. Vents must be cut down through the floor, screening and filters installed, and baffles installed to keep the incoming and outgoing exhaust air separated. 

Also this week, arrangements have been made to finally acquire the two 100-watt solar panels, tilt rods, wiring, controllers and even the roof rack. Barring any unforeseen circumstances, that should happen on Monday. And before any of that can be installed, I still have to order the special rust-eating paint for the roof, and then apply two coats of Kool Seal roof coating to it. So there's lots more of this boring fun coming. (:>)

I am currently working on a solar water heater design, and researching components, weights, and other such things necessary to make it safe for roof-top mounting. This will be a much more efficient design than simply attaching a black pipe to the roof rack, and will keep the water hot for a much longer time...good news for those wanting to shower after the sun goes down! So keep watching for that in the not too distant future. It will solve many of the problems with boondocking without power or the need to use space and propane for a typical RV water heater. And forget gravity fill and feed. This system will be pressurized from the water pump!

We're down to about 106 days before we leave at this point, so the time will go quickly. Whatever we don't get done here can be done on the road, and that includes final trim and painting. Right now, we are more concerned with getting the cabinetry and systems installed so we can at least "function" on the road. I'll have a lot more time for the little miscellaneous things after we leave here. 

By the way, if you are on a mobile device, and my countdown timer is not showing, I apologize. It seems to work fine when viewed on a laptop, but I noticed on my iPad, it disappeared again. I had this problem once before, and had to reload it from the third-party web program, It worked for awhile, but has now messed up again. Sorry 'bout that. I'll try to fix it when I get time.

We still have a lot of household items to dispose of yet, set up a local temporary storage for the rest, arrange for mail forwarding, and a ton of other things to do. This is also why I haven't been working on updates to my ebook, for those of you who have downloaded the free copy. Get it while you can, because I hope to have the paid version (as in "not free") going to Kindle by this next winter. There's a lot of good information there for any size or type of RV you are using. Everyone will get something from it.

But this post is long enough already, so let's take a break here. Let me know your thoughts, and if you have any questions, please ask.



Sunday, April 5, 2015

Bulkhead Wall and Starting Cabinet Building...

OK, I think I've milked all the publicity out of the Ed and the Aberts video (previous post) that I can get. (:>). Time to move on.

Despite my absence of posting over another crappy winter, I have been making slow progress as weather permits. I just got sidetracked from uploading pictures from the camera and doing regular posts. Now that the weather is finally warming up, I should be making more regular posts...and progress. After all, as of today, we only have 113 more days, and we're outa here! (Hopefully).


The new step...


In reviewing the photos I uploaded, it looks like the first thing that happened was to finally build a step. Even though the trailer is fairly low to the ground, it is still a good 14 inches to the threshold, which is roughly double a standard step riser height. And we aren't getting any younger. So, first I rounded up some scrap treated 2 x 6's and made a rudimentary step that will suffice for our needs.

Our new 2 x 6 treated step.
To keep the step solid, it is assembled with 2-1/2-inch deck screws, with a center cross piece to keep the legs stable. the 5-1/2-inch nominal board width, topped with another 1-1/2-inch flat piece brings it up to exactly 7 inches, or half the threshhold height. Of course, that may change slightly, depending on the levelness of the ground the trailer is parked on, but it will be fine. And we can always add another board under it if we have to. We just have to get in the habit of ducking our heads when going in, so we don't come up under the top of the shorter than normal doorway. Been there, done that. It hurts!

The bulkhead wall...


The next project was to build the bulkhead wall. The framing pieces were cut first, but then the weather changed for the worse. I also discovered at that time that my pocket hole drill bit was broken, and had to order another one. Then I realized that I wouldn't have enough screws to do all the cabinet frames, so I ordered a 500-count box of screws. Both came from Amazon.

I used to have a biscuit cutter set and cutter for my larger router, but sold all of that in last year's garage sale. For those not familiar with joining biscuits, they are basically little football-shaped plywood pieces, about a 1/4-inch thick and two inches long. The cutter is a thin bladed disk that fits a router. It cuts a semi-circle into the middle of the wood joint, into which is glued a biscuit. But you still have to clamp the joint for a tight fit. With pocket hole screws, the screws pull the joint together, and no clamps are needed. 

Driving screws into the pocket holes.
I used my Black and Decker clamp table to hold the aluminum pocket hole jig while I was drilling the holes, and then used it again to hold the pieces of the frame while I screwed it together. The screws go in at an angle, and pull the pieces tight, but it also helps to use a couple of scrap pieces of wood on either side, clamped tight to keep everything flush.

Holding the bulkhead wall frame during assembly.
It was a little awkward working with such an assembly in such tight quarters, while trying not to bump anything and jar it loose, but I got it done. Above is the wall frame without the cross pieces for the electric heater opening. The wall, by the way, is 68-9/16" long by 40" high. The height was determined by the height of our bicycle handlebars, as they will be the main things stored in the back of the trailer, below the rear bunk.

The cross pieces being clamped for the electric heater.
In the above photo (please excuse the cell phone quality) you can see the cross pieces being installed for above and below the electric heater opening. Note the pocket holes for the screws that hold it together, and the clamps to keep the pieces flush. All joints were glued with Elmer's professional grade wood glue. Now it was time to move the entire assembly to the garage, where I could lay it flat for cutting and inserting the rigid foam insulation into the voids. I raised it off the work table on 2 x 4's just so I could reach under to check the underside, in case the foam pushed through too far.

The bulkhead wall, ready for insulation.
Note that the end pieces were wider than the center pieces of the framing. This was to allow for the installation of four barrel bolts, which were to hold the wall in place at the side walls of the trailer. I have since decided to forget about that. There is no need to remove the bulkhead wall once it is in place, as the piano can be loaded through the side door. So now, just a couple of 3/4-inch square stops, screwed to both the back of the bulkhead and the trailer sides, will hold it all in place. The middle will be strengthened by securing it to the cabinets on either side, in front of the bulkhead, so when all are secured, it won't move...even in the middle. Also, the bunk that sets on top of the wall will also have cleats under the front edge to go over the wall. It won't go anywhere.

Foam insulation in place in the bulkhead wall.
Since the storage compartment will be unheated, even though it will be contained within the trailer, I thought it prudent to add insulation to the bulkhead wall. I will also insulate under the bunk, as well as the wall at the very rear that goes all the way to the ceiling. In other words, when the ramp door is open you will not be able to see the upper bunk...just a blank wall.

We don't plan to remain in temperatures below 40 degrees, although overnight temperatures may dip below that, even in Yuma during January. But it also doesn't take much to heat such a small space, either. At this point, I have no intention to insulate the floors. We may put some rugs down if it gets too cold, or even add an electrically heated floor mat if necessary. We can't use it boondocking, but if it gets that cold for very long. we'll go somewhere with an electric hookup, and revert to our electric heaters, rather than waste propane for the Mr. Heater Big Buddy that we plan to buy.

The back side of the paneling being cut for the bulkhead wall.
At this point, it was time to cut the facing material for the bulkhead wall. I happen to have several pieces of nice blonde paneling, that will work well. Originally, my intention was to paint everything white, but since I discovered all this very light paneling, I will use it on most exposed flat surfaces except for the walls of the trailer. The face frames will be painted a complimentary color, as will the trailer walls. The ceiling will still be white. But the exposed ends of cabinets, and maybe the undersides, too, plus the front of the couch, can all be paneled. We think this will look very nice when we're done.

Note in the above photo, the six-foot aluminum straight-edge clamped to both sides of the panel. Rather than try to feed this large a piece through my table saw, and take a chance on damaging it. I used my contractor grade Ryobi circular saw. It has a large 1/4-inch thick base plate on it, that rides against the straight edge, giving me perfectly straight cuts every time. The paneling is raised off the table top with scrap 2 x 4's under it, and the saw blade is set to a shallow depth, so as not to cut into the table.

Note also, that the piece of paneling is laying face down. That's because the circular saw blade cuts "up", and any splinters that may pull loose will be on the back side, while the front remains perfectly smooth. On a table saw, it would have to be laid face up, because that saw cuts "down".

For our project, I am using the nicer paneling on the interior side, but the back side of the bulkhead wall is going to be plain old 3/8" CD grade plywood, and it will be painted. The reason for the heavier choice on the back side is that I plan to attach a couple of steel tool boards to the back side, and may end up attaching some other things there. For one, I want a place to anchor some ratchet straps to secure the two bicycles. I wouldn't want them bouncing around and getting all beat up.

However, I discovered an anomoly in the piece that I chose. It had a manufacturing defect in it. Somehow, a stray piece of plywood got caught in the gluing press and attached itself to the sheet of plywood. I could hide it by putting it toward the wall, but it would still stick out enough to cause a bump in the wall. So I got out the hammer and chisel and proceeded to chisel that bad piece out. The groove that it left won't be a problem...but a bump would.

An impressed splinter on the back of the sheet of CD grade plywood.
Personally, if I were a quality control inspector, this kind of crap would never make it to a lumber yard. It belongs in a salvage yard! But this is the kind of stuff you get occasionally, and if it's too bad, or unusable at all, the best thing is return it to the lumber yard and let them figure out how to dispose of it! You shouldn't have to pay good money for this kind of quality!

The rear side of the bulkhead wall, with the heater opening cut.
But once flipped over, and cut to size, the plywood will work fine for the back side. The heater opening was carefully measured and cut before the sheet was attached to the wall. Once the sheet was in place, it was secured with heavy duty 3/4-inch long, 1/4-inch crown builder's staples, shot in with my Bostitch pneumatic stapler at 100 pounds air pressure. Then I flipped the wall over again to add the nicer paneling to the other side. You always want to do your worst side first, in case of scratches, and then do your finish side when ready to install the wall.

The interior side of the bulkhead wall, with the heater opening cut.
The same process was used to install the interior paneling, with two exceptions. (1) this paneling had to be installed in two pieces, with the butting edges perfectly matched so as to make the joint appear non-existent. And (2) the air pressure on the stapler had to be reduced to 60 pounds...otherwise it will drive the heads right through the paneling! 

There were some previous nail holes in the salvaged paneling, but nothing that a decent blend stick will not fill. But minor things like that can always be done after we hit the road. My main concern now is getting all the pieces in place in the trailer. The cosmetic stuff can wait.

Once the wall was temporarily set in place in the trailer, I attached the electric space heater to it. The back side of the heater projects through the wall slightly, but that was planned. The cord comes out the bottom past the wall, and will plug into my power distribution center on the left wall of the storage area. 

The back side of the bulkhead wall showing the heater installed.
The front side looks nice with the trim installed on the heater, and is exactly as planned.

The interior side of the bulkhead wall with the electric heater installed.
So now all that is needed is to install the 3/4-inch square stops down each side of the back of the bulkhead wall, and that part will be done. But before I do that, I want to build the cabinets that go against that wall. This will allow everything to join together without strain, and find their own natural place.

The itty bitty closet...


Although I have the face frame pieces cut for the "accordion closet" and ready to drill for pocket holes, I decided to go ahead and get the other side cut, and since it was smaller anyway, and I didn't have enough width for pocket holes, I just went ahead and assembled it with glue and clamps.

As I said, due to having to move the bulkhead wall forward more, the extra 4 inches had to come from somewhere. I couldn't take them from the wardrobe closet because we have to have a minimum of 31-1/2 inches to store the Bivouac Buddy shower enclosure against the back wall. The rigid pan on it won't collapse any smaller. We couldn't steal from the kitchen cabinet, because it is already laid out to fit a 48-inch width for everything that it must contain.

Between it and the front couch, I need a minimum 13 inches for foot space for my size 13 shoes, so I don't have to twist sideways when sitting at the flip-up counter extension. And the couch is already sized to our needs, with coming out from the wall 21 inches in couch mode, and extending to 34 inches in bed mode. It will be up against the kitchen cabinet in bed mode.

So the only thing to do was "narrow up" the only closet I could. Originally it was going to be a shirt closet...but no more. Unfortunately, it will only be good for flat items laid on edge now, but so be it. I told Sharon she could store her cookie sheets in it. (:>) 

Since the entire height was of no advantage anymore, I decided to put a shelf in it, about two-thirds of the way up. For ease of access, the top will remain open. There will be a piano hinge on the upper bunk platform right at the edge of the bulkhead, so the front can be lifted out of the way when getting into the lower cabinets. But it will normally remain in the down "full width bunk" position, so the little cabinet will be covered most of the time. On the opposite side will be a similar but wider (about 14  inches wide) short closet which will hold Sharon's accordion on the bottom, and a file folder box on the top. That will also remain "open top" and be covered by the front portion of the bunk platform.

The cabinet frame for the left side in front of the bulkhead wall.
I'm not even sure about whether to add doors to this little cabinet, but I probably should, just to keep things from sliding out. Due to their location and what they were for, I did not create a toe space at the bottom. These go all the way to the floor, as will the wardrobe closet and couch. Only the kitchen cabinet will have a toe space, because that is the only one we will have to stand at to work at the sink.

Narrow cabinet with sides attached.
Once I had the frame built, the next task was to add sides to it. They didn't need strength, so I found a scrap piece of eighth-inch paneling. It didn't match the other pieces but it didn't have to. I chose to put the back side facing in and the face side out. No one will see it anyway, as the left side will go against the bulkhead wall, and the right side against the wardrobe closet. Only the face and top will be showing. The inside will be just clean bare wood, the same as most cabinets of this type. I did find some 1/4-inch white Masonite paneling to use as the shelves, just to brighten it up a little. Once it was done, and the face sanded lightly, I carried it out and set it in position in the trailer.

The wardrobe closet...a start, anyway...


The next project, still waiting for some warmer weather, is the wardrobe closet. I have the face frame, jambs and stops assembled, but didn't get a photo of them this time. In order to get them into place in the trailer, I can't build the whole closet in one piece. It will have to have the walls built first, and then set into place. There will be no back on it. The walls will be secured (by screws) to the walls of the trailer with the same kind of 3/4-inch-square stop used to anchor the bulkhead wall. Then the face frame/jamb will have to be attached after they are where they all belong.

One wall of the wardrobe closet, top end near the bottom of the photo.
The wider piece at the top was necessary for three reasons, (1) for the contour of the top to be cut from one piece, (2) it will provide plenty of backing for which to attach the closet rod, and (3) the square bottom allows the studs to be all cut to the same length, for ease of assembly.

The angle on the bottom right is to fit over the angled cover that will go over the curved portion of the ceiling edge. I was originally going to fit aluminum flashing into the curve, but decided that it wouldn't leave enough space for wiring and other things to be fished through behind it. Instead, I will make paneling covers for it, to be screwed into place, in case I ever have to get behind them. Basically it will be a "utility chase". There will also be an angled cover in the right rear corner of the wardrobe closet to get wiring from overhead to the battery compartment at the bottom of that closet.

If there are any "irregularities" in the contour of the tops, it won't be much, and will eventually be covered by flexible trim, so minor gaps are unimportant right now. After all, I'm not running a CNC shop here, nor do I have that kind of equipment. Caulk, trim and paint are my friends. (:>)

I started the frames for the wardrobe closet walls, but ran out of time to get all the parts drilled for pocket holes. Then the weather turned cold and wet again. Tomorrow, the day after Easter, is supposed to start a warming trend again, so I plan to be working more often and longer each day as the weather improves.

But at least I have the tops cut and contoured (close enough) to fit the ceiling of the trailer, and even the paneling is cut for the exterior of the closet. I just have to cut the interior panels yet, and then it can be assembled and installed in the trailer.

Final thoughts...

The pegboard...


I mentioned earlier that I was going to add steel tool board on either side of the electric heater in the rear storage compartment. I just happened to have one piece that was not currently being used elsewhere, and decided that my makeshift tool bench in the trailer was overcrowded and a mess. So I used a couple of steel S hooks scavenged from some rubber truckers bungees, and hung one piece of it over the bench...horizontally.

Half-sheet of steel tool board temporarily hung on trailer wall. 
Once the bulkhead wall is fastened in position and painted on the back side, this tool board will join another just like it, and be installed vertically on each side of the electric heater.

This is just one piece of the very high quality tool boards that a work associate and I imported from Sweden in 2004. It has about twenty different styles of lock-on hooks and attachments, plus three sizes of bins that fit on it. There are also plain attachments with screws in them, from which you can attach any kind of special anchor of your own design, from shelves to special fixtures. These hooks have to be manually removed. They can not fall off while going down the road. However, the tools themselves can fall off the hooks if the wrong type is used. For our trailer, we will be using mostly spring clip type attachments in three different plastic sizes plus steel ones. We also have some steel rings, that might be used for the ratchet straps to secure the bikes.

We see this as a good place to carry our four-foot-long BBQ forks, collapsible fan rake, a shovel and whatever small hand tools we need to keep available. Any other general hand tools are going into a lockable flight case with wing pallets in it.

My table saw setup...


The last thing I want to mention for this post, is the table saw setup I use.

My Rockwell Compactool 6-inch table saw and folding table.
When I graduated from high school, I won the North American Rockwell Corporation Award for Excellence in Industrial Arts. As part of that award, I received three pieces of shop equipment from the new (at that time) Compactool product line...the 6-inch table saw shown, plus a table model drill press and a 4-inch jointer. These tools are now 49 years old, and still work like new, although I have replaced the motor bearings on the saw once already, and the drill press now needs a new cord on it. I really had no use for the jointer in future plans, so I sacrificed it to a person who really wanted it and will take care of it...the husband of one of our postal workers.

I built the folding table back in my apartment management days. It was originally a 5 x 9 oversized sheet of 3/4-inch plywood, designed to hold rescreening equipment for the patio door screens. Then I got the idea to cut one end of it so my small table saw would fit into it flush with the top. After I left the apartments, I shortened it to six feet long. Now I can cut larger pieces, like full sheets of plywood, doors, shelving, or anything else too large to fit on a small table top. I also fitted it with folding "library table" legs, so when not using it, I can lean it against a wall, or transport it to a job site. It has been very handy over the years, but will be sold before we leave here. Not the saw...just the table. I'm keeping the saw and the drill press for my own puttering around.

Going forward...


So that's where we stand right now. I should have the closet walls done and assembled in the trailer by tomorrow evening, and hopefully get the other short closet done, too.

Then comes the nightmare project...the kitchen cabinet unit. It will have several drawers on side-mounted slides, two pull-out pantries, space for one of our 8-gallon Reliance Hydroller fresh water containers (several others will be spares in the van), a water pump, a future electric water heater (maybe), plus the bar sink and all of its plumbing, along with extra reinforcement for the weight of the countertop mounted refrigerator. Oh joy. It will be a work in progress for awhile.

And keep in mind that all of this is being built the same way as any cabinets are...in modular sections...so that in case we decide to upgrade to a slightly larger 7 x 14 trailer, we can remove screws and pull all this stuff out and put it right back in a new trailer. I certainly don't want to have to build it all again!

So what do you think so far?  Out of all the subscribers I have, there should be more than the same two or three all the time that have something to say. So how about it? Something...anyone!